-
No Hub-SML DS Offset Bend
DS CAST IRON Off-set
Cast Iron Fixed Offset Bend is available with a 130mm projection, and is used to direct a soil system around cornered obstructions, whilst keeping the system parallel. The bend is manufactured to EN877 using solid cast iron and finished with a Epoxy paint coating that complements the aesthetic of period buildings. -
No Hub-SML Cap with Rubber Seal
It is constructed of high quality cast iron. It is easy to install.
For use where a watertight seal is needed -
No Hub-SML 45°Single branch
Used to bring horizontal and vertical pipe runs together, usually when connecting a pipe from a WC into the main soil stack. The 135 degree angle introduces a steeper fall to the horizontal run than a standard 92.5 or 112.5 degree branch. It is most commonly found on the outside wall of a building, often on blocks of flats or apartments. -
No Hub-SML 88°Large Radius Bend with Access Door
SML 88°Large Radius Bend with Access Door, foul and surface water drainage system
Includes a wide variety of components, such as Bends, Junctions, Rodding Access and Access Fittings, together with Inspection Chambers and Manhole Bases.
-
No Hub-SML 88°Large bend
Cast Iron SML 88°Large bend
Cast Iron SML is a dry-jointed, lightweight cast iron drainage system, primarily used for above ground soil and waste drainage but also for rainwater installations
High strength, low maintanence system
Quick to assemble
Agrement EN 877 -
No Hub-SML Top bend
EN877 SML Top bend
Material: Grey Cast Iron
Coating: SML,KML,BML,TML
Product description：The pipe fittings have smooth surface, high density and strength, reasonable design in structure, beautiful externality used on high buildings and environmental protecting. -
No Hub-SML Vent bend
SML Vent bend
Material: Grey Cast Iron
Coating: SML,KML,BML,TML
Product description：The pipe fittings have smooth surface, high density and strength, reasonable design in structure, beautiful externality used on high buildings and environmental protecting.
-
No Hub-SML 45°Bend
Cast Iron SML 45°Bend Cast iron
Cast Iron SML is a dry-jointed, lightweight cast iron drainage system, primarily used for above ground soil and waste drainage but also for rainwater installations
High strength, low maintanence system
Quick to assemble
Agrement EN 877 -
floor drain
A floor drain is a plumbing fixture that is installed in the floor of a structure, mainly designed to remove any standing water near it.
Floor drain DN200*100 -
No Hub-SML 88° Bend with 250mm
Dimensions
Size : 250mm
Bend Angle : 88°
Description
Easy to install our Sewer drainage range includes solid pipe and fittings. A combined lip and compression seal into its solid pipe which is secure against dislodgement and makes jointing easier ensuring that joints remain leak free for years to come. -
No Hub-SML 45° bend with 250mm
Dimensions
Size : 250mm
Bend Angle : 45°
Description
Easy to install our Sewer drainage range includes solid pipe and fittings. A combined lip and compression seal into its solid pipe which is secure against dislodgement and makes jointing easier ensuring that joints remain leak free for years to come. -
EN877 BML Pipe Fittings
DS MLB (BML) Bridge drainage pipe fittings is has typical properties of resisting acidic waste gas, road salt mist, etc. suit-able for special requirements in the field of bridge construction,roads, tunnels with its typical resistance of acid exhaust fumes,road salt etc. Furthermore, MLB also can be used for underground installation.
The material is cast iron with flake graphite as per EN 1561, at least EN-GJL-150. The inside coating of DS MLB fully meet EN 877; the outside coating corresponds to ZTV-ING part 4 steel construction, annex A,table A 4.3.2, construction part no. 3.3.3. The nominal dimensions range from DN 100 to DN 500 or 600,length 3000mm.